Polyglass Polystrip SA is a self-adhering waterproofing tape composed of a slip resistant surface and UV resistant film laminated to an aggressive elastomeric (SBS) modified asphalt adhesive. The adhesive is protected by a siliconized release paper which allows quick and accurate installation.
Polystrip SA seals the roof deck seams and other construction details in compliance with project and/or building code requirements where a self-adhesive strip meeting ASTM D1970 standards is designated.
Polystrip SA may be covered with any Polystick or Polyanchor roofing underlayment or roofing felt. Polystrip SA can also be used as a general flashing membrane.
Typical Applications
- Designed for applications on new or re-roof projects over roof deck joints
- May be covered with Polyglass Polystick or Polyanchor underlayments
- Can also be used as a general flashing membrane
- Adhesion to plywood, OSB, metal and other approved substrates
Features and Benefits
- “Seal the deck” joints from water intrusion.
- Slip resistant walking surface.
- Highly flexible and lay flat characteristics; transitions over uneven joints.
- Asphaltic rubberized compound provides excellent sealability around nails.
- Approved up to 250°F
- Up to 60 days UV exposure.
Polystrip SA – Roof Deck Joint Tape Take-Off Calculator
Designed to help roofing professionals estimate how many rolls of Polystrip SA joint tape are needed based on the square footage of a roof. Estimates are based on standard measurements for plywood and joint spacing to calculate the total linear footage of deck joints and provide an accurate roll count.
Product Packaging & Dimensions – Polystrip SA
| 4″ Wide |
4″ (10.2 cm) |
67′ (20.4 m) |
12 |
804′ (245 m) |
| 6″ Wide |
6″ (15.2 cm) |
67′ (20.4 m) |
8 |
536′ (163 m) |
PolyVap SA S is a non-asphaltic self-adhered vapor and air barrier for use in commercial low-slope roofing applications. This membrane features a high strength polypropylene sheet with an aggressive acrylic based adhesive on the bottom that bonds to most substrates.
PolyVap SA S is a carrierless membrane and surfaced with a slip resistant top to enhance walkability. This membrane can be used as a temporary roof for up to 180 days.
The top surface is compatible with approved coverboards and Polytherm insulation; mechanically attached or adhered with Polyglass LRF (low-rise foam) adhesive. Polyglass offers a variety of waterproofing membranes to complete the roof assembly.
Features and Benefits
• Aggressive self-adhesive for wind uplift performance
• Impermeable to air, moisture, and water
• Slip-resistant top surface compatible with Polyglass LRF (low-rise foam) adhesive.
• Weather install temperatures from 20°F and rising
• Direct to metal deck application; no primer required
Polyvap SA G is a self-adhered vapor retarder for use in commercial low-slope roofing applications. Utilizing ADESO® dual-compound self-adhered technology, Polyvap SA G features a polymer modified bitumen upper compound and a proprietary self-adhesive SBS (elastomeric) compound on the bottom. A split release film that protects the self-adhesive compound allows for easy application.
Polyvap SA G is reinforced with a fiberglass mat, and surfaced with aggregate to enhance skid resistance and allow exposure up to 90 days. The rubberized asphalt seals around correctly installed nails on the weathering surface.
TWO SIDED, PRESSURE SENSITIVE TAPE SPECIALLY FORMULATED FOR BELOW GRADE DETAIL APPLICATIONS
Mapeproof AL Detail Tape is designed to bond to concrete and prevent lateral water migration in the most complex of job site details. Forms a strong bond to Mapeproof AL, ensuring watertight details with enough durability to accommodate foot traffic. Comes in convenient 4” and 8” roll sizes.
Features and Benefits
- Flexible and easy to apply for watertight details
- Forms a continuous adhesive bond to concrete preventing lateral water migration
- Multilayer design enhances durability and allows foot traffic
POST APPLIED SELF-ADHERED WATERPROOFING MEMBRANE FOR BELOW GRADE STRUCTURES AND ELEVATED DECKS
The specialized formulation combines a rubberized adhesive with an HDPE layer to act as a barrier against moisture, water and gas. Mapethene LT60 membrane is suitable for installations where the ambient temperature is between 25°F – 60°F (-4°C – 16°C). See Mapethene HT60 for high temp applications.
Features and Benefits
- Cold applied without using flames
- Factory controlled thickness
- Low temperature applications
- Highly flexible; simple, quick and easy to apply
- Self-adhesive overlaps and excellent adhesion to various substrates
- Elastomeric, can accommodate concrete shrinkage
- Excellent chemical resistance and protection against gas vapor intrusion